Run kitchen cabinets

Manufacture of kitchen cabinets

The steps of building and installing a kitchen cabinet are as follows:

Initial design, measurements for the execution of the design and the exact construction of the kitchen cabinet, the design of the kitchen cabinet, the type of materials, calculating the size of the cabinets for cutting, cutting the "cabinet", pasting the edges, sliding the kitchen cabinets, assembling Cabinets
An initial plan is made to build cabinets to provide explanations to the buyer of the cabinet, and depending on the tastes and requirements that the original design will run.

In the second step, we go to the kitchen where the cabinets are to be installed. In the measurement stage, the stove is set and the electricity, chimney and gas splits must be located there. The type of gas is determined to be gassed or conventional gas is supposed to be used, if used with conventional gas, 90 cm of space should be considered for it, and if you use gas from the gas, some place on the cabinet wall is empty and We put the gas space down into the cabinets. Determine the hood installation location and whether the cabinets need to be installed, usually the space used for the hood is from 60 to 90 centimeters. The place of installation of a washing machine and dishwasher must be specified and for each space 60 cm should be left blank. About 95 to 180 cm space for the refrigerator should be left blank. They usually install cabinets above the refrigerator space. The location of the sink, which varies depending on the splits of the water pipe, varies. Some people will need space in the design of the cabinet, depending on the tastes and needs. At the end we determine where the drawer is or how many series, and if there is enough space, we will design a showcase for decorating.
The design is carried out according to the size of the kitchen, which is either manually executed, engineering design is done on paper or computer-aided by software such as 3Dmax, Catia, etc. .
The refrigerator, stove and sink should be easy to access, since most of the work in the kitchen is with these three tools, it's better to be close together to get things done faster. At the design stage, all the building disadvantages and drawbacks should be taken into account so that the most beautiful design is possible for that space and a beautiful and comfortable kitchen designed to be the main task of the designer of the kitchen cabinet.
For the manufacture of cabinets, they use particleboard, mdf and laminate panels with artificial and natural coatings on the market. For panels with cabinets that are directly connected to heat, water and wear, they use panels with a thickness of 4 cm and high resistance coatings.
Run kitchen cabinets

Installing a kitchen cabinet

Cutting is done in two steps. In the first step, the wooden sheet is crushed, and in the next step the cutting is as large as the boards. Door cuts, open view and floor cabinets are installed after installation.

At the edge of the adhesive that works for beauty, it is made with PVC or wood strips, the thickness of these strips is between 0.1 and 2 mm and protects the edges of the work against water penetration and moisture and shock. Bottles that have a smaller thickness are used for the floors of the kitchen cabinet, and the strips that are thicker are used for the kitchen cabinets. The adhesive edge is done in both machine and hand.
The next step is a hole, which will make the assembly work faster and more accurately and the result is clean and beautiful. The perforated hole must be perpendicular, with a distance of 5 cm from the edge of the work. The holes in the body of the cabinets, the rails and the lower floors are projected.
And finally, the assembly of the kitchen cabinet is where all cabinets are connected to each other according to the original design. All these steps should be carried out by an expert, because the installation of the cabinet requires high skill. At the assembly stage, we should mark this on the wall. It should be done carefully and the lines drawn should be aligned, which is a mistake at this stage causing disadvantages in the entire installation process. Fit the fittings on the wall. These fittings should be tight because they should bear a high load. By installing these connections, the installation of the kitchen cabinet is carried out with great speed and precision. It installs cabinets on fittings. First, they install cabinets and cabinets together, they align with the base of the cabinet, and then mount the cabinets on the wall and tie together. Next, installing the screen is a cabinet, and after installing it we will install a sink or a desktop gas. After installing the kitchen cabinets, we measure the cabinets, the interior cabinets and the open view, and cut them.
Once the cabinets are installed in their place, it is time to measure the doors of the cabinets with their open facades and their floors. After cutting, we slip through the edge of the PVC strip. We install hinges on doors. Hinges should be used according to the weight of the doors, otherwise the doors will be dusted after some time. After that, we install the doors and regge them, put the floors in the cabinet and the open view.
How to install a kitchen cabinet

Movie Install cabinets kitchen

Tags: production of cabinets, kitchen cabinets manufacturing, cabinet production workshop, kitchen cabinet design, cabinet design, cabinet workshop, kitchen cabinets installer, cabinet installer, cabinet installation, cabinet installation method, cabinet manufacturing method, assembly of kitchen cabinets, assembly of cabinets, assembling Kitchen cabinets, Door cabinets, Cabinets workshop, Installation cabinets training, Kitchen cabinet assembly training, How to install kitchen cabinets, MDF cabinets, MDF cabinets, MDF kitchen cabinets, installation process cabinets, stages of production of cabinets, installation of kitchen cabinets , Cabinets work